When I was learning to paint, living where I do on the shores of the Bay of Fundy, boats of all sorts were a readily available subject. I ended up painting a lot of boats. I have always been drawn to the water and boats were an excuse to paint water. People who know boats will not accept a painting of a boat that looks like she will sink. Over the years, through trial and error, I have learned how to render a boat that looks seaworthy.
Whether elegant sailing vessels or battered fishing craft, boats are a challenging subject. Personally, I find it easier to accurately portray a boat than a building. Mind you, I paint boats far more often than architecture. As a result, boats come more easily to me. It is a matter of practice and familiarity with the subject.
When asked “How can I learn to paint boats like you?” my reply is only-partially tongue in cheek “Paint a lot of boats. Make lots of mistakes, learn from them, eliminate those mistakes from your painting vocabulary and finally what you are left with is the ability to paint a good boat.”
In our house we actually have a term for a poorly rendered boat. We say it is suffering from “Wonky Boat Syndrome” Sometimes it is terminal condition. Most usually a terminally wonky boat is suffering from a fatal error in drawing.
The key to portraying anything correctly is taking the time to look at it closely and to identify the relationships that make it the shape it is. In other words, the key is knowing how to draw. Whether you use a pencil or a brush loaded with juicy oil paint, you need to be able to see the shapes and get them down in front of you.
I learned how to paint in watercolour long before I took up oil paints. In watercolour, pre-drawing is pretty much crucial. In oil painting drawing is still key to rendering a good boat. The blessing with oils is that I can start with a loose representation of the shapes in the approximate right place. As I work I can move them around, correcting as I go. Small adjustments make the difference between a boat that will float and one that would sink.
Here’s how I go about rendering a boat.
I take a good look at the darned thing. I really look at it. I rough in the shape. This next step is the important bit: I look at the boat again and compare it to the shape I just made. I fix the most obvious error and then I compare it again. Fix it again, compare again. Over and over, until I am done. In words this sounds simple. In practice it’s a bit more challenging, especially if the boat is twisting at a mooring.
That is a problem with boats. They move. The tide goes out and suddenly you notice the boat is several feet lower from the top of the wharf than it was before. (Or several meters if you are in my beloved Bay of Fundy.) The wind comes up and shifts the boat from a bow view to a stern view. The skipper comes along, hauls anchor and sails away. Drawing a preliminary sketch in a sketchbook can help, learning to capture shapes quickly can help, too.
I painted
Here are some common reference points that I check as I draw a boat.
I get the big shape right first, paying attention to relationship of the height of the hull to the length of the hull. Is it 3 times as long as it is high? 5 times? Get that correct first. Then I include the cabin, if there is one. Rough it in, paying attention to size relationships again. Is it the same height as the hull? How much of the length of the boat does it extend?
In this painting, the closest boat is approximately 4.5 times as long as the height of the hull at the bow. The front face of the cabin is slightly more than half the height of the hull and is set back from the bow about the same distance as it is tall. The cabin shape ends at about the midpoint from bow to stern. I pay attention to these relationships, and yes, if I am painting outside, I stand there with my brush in my hand and I hold it up and I measure.
Then I start looking at the finer points.
Look closely at the mast, if you are painting a sailboat. In your rendering, does the mast come up from the centerline of the boat (ie does it sit in the middle between the two sides?) It should.
Look at the line of the bow and the stern (that’s the rear). Are they straight up and down? Are they slanted one way or the other? Different boats, different angles. Pay attention. Look closely.
Pay attention to all these little details. Look at what you are painting. Even if you “know” boats, look at the one that is in front of you. Compare what you have drawn to what you are seeing. If something looks wrong, measure. Keep measuring until you find where the problem has crept in.
Is the waterline straight? Boats sit in the water. The water surface is flat. Even though boats are full of curves everywhere, water still follows the laws of gravity. If looking at a boat from the side, the waterline will appear straight and run parallel to the horizon. (It can be broken up by waves, but overall should be straight.) If the boat is at an angle receding away from you this becomes more complicated… Then you have to look closely. Measuring helps. Hold your brush up in front of you and line it up against the waterline of the boat. This shows you the degree of angle if there is one, and if there is any degree of curve. You’ll be surprised how often there is no curve when you thought there was one.
This ship is over 63′ long and pointing almost directly at us. Despite that, her waterline looks relatively flat, because this picture is from just about water level.
Where is the boat in relation to the horizon?
Remember that the horizon line, the true horizon, where the sky meets the water, will always be pretty much at your eye level. This means if you are at the water’s edge, the horizon might be just above or even behind the boat you are rendering. If you are up a hill, or on a high pier, the boat will be further below the horizon line, so much so (depending on how high up you are) that you may not even be able to include the horizon in your picture.
In this next drawing the vantage point is higher than that from the painting above.
(Conversely, where are you in relation to the boat?)
The boats are depicted with a vantage point from the road running above the shore, so they all fall below the horizon.
Placing your boats correctly in relation to the horizon line becomes especially important when you are painting a group of boats. This is to avoid that sub-genre of Wonky Boat Syndrome, the Tiny Boat Illusion. Perspective applies to boats just as much as it does to buildings in a city. If you have two identical boats, one near and one far, they will maintain proportionally the same distance from the horizon line.
Here I’ve drawn in some perspective lines:
Then I added another boat, one that is proportionally out of place.
Do you see that it is actually the same size as the left-most boat?
Finally, here is an illustration showing the relative ship height and the horizon. Those marked in red, you will note that the height of the boat is roughly double the space between the top of the boat and the horizon. The center boat, marked in green, does not match that proportion and hence looks like a tiny boat.
I have given a laundry list of some of the problems I have seen most often in painting boats. I have certainly made all of these mistakes and more. The important thing is to learn from them and move on. That is, after all, what creates
There is plenty written about rendering boats accurately. For another perspective on how to avoid missized boats, please visit James Gurney’s post on the “Toy Boat Problem”
Leave a Reply